CS CASE Impact safety valve Model 07151 Size 1/2"

Guidance for buying CS CASE Impact safety valve-07151 Size 1/2"

CS CASE valve safety valve model 07151, size "1/2" has been produced and supplied to discharge the excess pressure load on the piping system; Balanced, so as not to damage the components of the piping system Increased fluid pressure inside the piping system can damage devices such as heat exchangers and tanks and even explode the system Model 07151 under EN1489 with three pressures Fixed 10, 6 and 3 times (without the possibility of adjusting the output pressure).
The important point in using this safety valve compared to large spring body pressure relief valves is that the consumer can not adjust the working pressure of the valve in a certain range.

Features and dimensions of CS CASE Impact safety valve Model 07151 Size 1/2"

• As mentioned above, the above valves are marketed in three different pressure ranges, with values ​​of 10, 6, and 3 times.
• Model 07151 is used in CCTV heating systems, boilers, solar energy systems, water supply facilities, and firefighting facilities.
• It should also be noted that these valves with DN 15 are used in boilers with a maximum of 200 liters.
• These safety valves can be used to pass two weather fluids.
• The operating temperature of the above products is from 5 to 110 degrees Celsius.
• The interesting thing about the term ticking (which is common in the control and safety equipment market) is that the red knob mounted on the top of the valve reacts when the pressure in the water supply network is unauthorized. The following explains how this product works.
• Can be used in piping systems
• Made in Turkey

Performance of parts and required information CS CASE Impact safety valve Model 07151 Size 1/2"

The performance of knock valves is based on the result of two forces in opposite directions;

1. Spring pressure force used in the safety valve
2.  Water vapor force

The air vapor force in the valve closed-circuit diaphragm does not cause the spring to move until the pressure inside the piping system increases. After the fluid passes through the diaphragm to the floor, the discharge takes place and the knob of the tap operates, in this case, the increase of unauthorized pressure is prevented.

Material of components of CS CASE Impact safety valve Model 07151 Size 1/2"

• Body: Brass
• Milk cover: rice
• Aperture: EPDM
• Spring: Steel
• Shaft: Rice
• Spring housing cover: PA6
• Manual drain cover: PA6
• Adjustable screw: PA6
• Segment: Steel
• Fuse or safety knob: Pro polyethylene (PP)

General information of CS CASE Impact safety valve Model 07151 Size 1/2"

• Operating temperature: 5 to 110 degrees Celsius
• Working pressure (non-adjustable): 10, 6, and 3 times
• Type of fluid used: Climate

How to install CS CASE Impact safety valve Model 07151 Size 1/2"

• Reducing water pressure on the diaphragm is done by applying two opposite forces to the diaphragm valve
• Compressed steel spring pressure
• Water pressure on the diaphragm
• If the spring pressure is higher than the water pressure, the piston moves upwards and if the spring pressure is less than the water pressure, the piston moves downwards.
• Maximum inlet pressure: 16 bar
• Operating pressure range: 6.5 bar 1 bar
• Factory outlet pressure: 3 times
• Type of fluid usable: water
• Maximum operating temperature of milk: 40 ° C

  
  
  Observe the safety distance of the valve from the safety valve device when installation.

  

  Dimensions of CS CASE Impact safety valve Model 07151 Size 1/2"

Size: "1/2
C: Equivalent to 24 mm
D: Equivalent to 42.5 mm
E: Equivalent to 35 mm

Warranty and authenticity of CS CASE Impact safety valve Model 07151 Size 1/2""

The company approves the originality and physical health of the CS CASE Impact safety valve Model 07151 Size 1/2"".
In the reference site and DamaTajhiz store, various types of valves have been provided for you, dear customers, in order to create a good feeling of optimal and smart purchase of valves.