Hepaco integrated plate Evaporator Model HPE-30

HEPACO integrated plate Evaporator Model HPE-30

HEPACO integrated plate evaporator HPE-30 provides immediate consumption and sanitary warm water with the minimum cost and without wasting energy with an efficiency of over 95 percent. To calculate the approximate integrated plate evaporator capacity for supplying sanitary water of residential units, consider 300 to 400 liters of evaporator capacity per unit.

Some of the most important specifications of the HEPACO integrated plate Evaporator Model HPE-30 include Material, working efficiency, and working pressure

• HEPACO integrated plate evaporator HPE-30 is integrated, water to water, gas to water, steam to water, oil to water type, etc.
• HEPACO integrated plate evaporator HPE-30 is fabricated from stainless steel S.S.316.
• To exploit the maximum capacity of the HEPACO integrated plate evaporator HPE-30, it is recommended to convey the fluids in parallel mode and in form of Counter Flow.
• Due to the thermal capacity of the warm water or hot water boiler and integrated plate evaporator selection in order access to adequate amounts of warm water for heat exchange is very important.
• The working pressure of the small HEPACO evaporators (models: HP40 to HP150) is equal to 10 bar and the working pressure of models: HP200 to HP1500 is equal to 30bar.
• Using steam with a pressure of up to 3bar as a fluid carrier of heat energy in HEPACO integrated plate evaporators HPE-30 is allowed.
• Interestingly, HEPACO evaporator HPE-50 in water-to-water type has a heat transfer coefficient of 5000W / m2cº, while resource-efficient heat transfer coefficient 500w / m2cº and double sources have a heat transfer coefficient of 500 W / M2Cº and warm water sources with coils have a heat transfer coefficient of 1250 W/M2 Cº.
• In the case of applying HEPACO plate evaporator HPE-30 for under-floor heating systems, it is recommended to consider about 136 kcal heating capacity per meter PEX pipe length on the floor.
• HEPACO evaporator HPE-30 with small dimensions, low weight, and high efficiency, reasonable price has very good performance efficiency.

Features Of Hepaco Heat Exchanger Model HP-30

• Fuel-saving up to 30 percent would be feasible by replacing HEPACO evaporator HPE-30 with coiled or double-jacket hot water heaters.
• HEPACO evaporators are provided in more than 20 different models and capacities and are always ready to supply domestic hot water instantly. They are also applied to provide Pools, buildings (floor heating), and all industrial applications heating loads.
• HEPACO plate evaporator HPE-30 provides maximum heating load capacity and has the minimum sediment coefficient compared to all common evaporators, which is because of applying a special design that creates perfectly sinusoidal turbulent flows of water with minimum pressure drop.

Tips for using HEPACO integrated plate Evaporator Model HPE-30

• In general, according to the deposition of mineral water’s salts after heating it, applying an appropriate softener on the cold water inlet circuit is necessary for the continued viability of all types of plate evaporators.
• As previously mentioned, in addition to the necessity of installing a softener on the water pipe of the evaporator HPE-30, installation of UNION and faucet on all inlet and outlet water pipes of evaporators is required for the possibility of periodic services and pickling.
• According to the necessity of applying one check valve and two filters and also a linear softener (magnetic, electronic, etc.) during installation and operation of plate evaporators, note to order them if the required equipment is not available in your project.
• When selecting the required evaporator, in addition, to calculating and determining the capacity and thermal level, evaporator type, sizes, as well as material and working pressure of evaporator, a pressure drop of water passing through the coils or evaporator plates (and air through the heat transfer coils) must be determined to obtain the circulating pump’s head or aeration fan static pressure.
• Accurate calculation of sweep water pipes diameter in HEPACO plate evaporators (where water is the working fluid) will lead to sufficient supplement of needed working fluid volume in an evaporator.

after-sales service of Model HPE-30

HEPACO plate evaporator  HPE-30 is offered with a one-year warranty and 10 years after-sales service. You can order and buy an evaporator at the best price from Damatajhiz website.